Replacement foot pegs for Cycle Cat

[The Bearded Duc]

Those are the toe pegs though, but good to know they are available. I got the last of MotoWheels extender toe pegs GL-1 two years ago.

Yeah, I can see the pics now. I was way off!! 

[Some Dude]

They pegs look great.   How soon do you think they will be available to ship?  I have PM'ed you my request. 

Hopefully 2 to 3 weeks

Those are the toe pegs though, but good to know they are available. I got the last of MotoWheels extender toe pegs GL-1 two years ago.

What are the extender toe pegs?

[The Bearded Duc]

What are the extender toe pegs?

Puts the toe peg out a little further, for those with bigger feet.

[Some Dude]

Puts the toe peg out a little further, for those with bigger feet.

Any idea how much further?  I was going to make up some toe pegs next, but if they can still be bought maybe i'll look at making extended length pegs.

[stopintime]

BTW, I think they were called GLE-1. They stick out, sideways, two inches measuring from the lever's outside.
They are a bit wider than ordinary Cycle Cat toe pegs because the eccentric arm is on the outside.
That was too wide for me - I reversed the peg/arm mounting so I had the eccentric arm on the inside of the lever, but then it was a little bit too short (or inboard if you understand).

If you make these - I think it's a good idea to make them less wide than the original two inches. Maybe about 1.5"

From center of arm pivot to center of toe peg is 25-26mm. Toe peg including eccentric arm is 2" wide.

[The Bearded Duc]

Any idea how much further?  I was going to make up some toe pegs next, but if they can still be bought maybe i'll look at making extended length pegs.

Check out the pics stopintime posted. They extend the toe peg about 25mm or 1 inch. They are still available to buy from motowheels.com but since you fab'd the foot pegs why not fab the toe peg as well, a little more custom! Keep in mind, you probably don't wanna go much further than 25mm as you might encounter clearance issues with the engine case?

[Some Dude]

Agreed with stopintime.  It can always be done by the end user with a dremel or other grinder but if you wanted to offer an upgrade to the Cycle Cat Peg, look into adding a textured lug/knurled lip to the outer edge.  This is where the ball of your inside foot rests while cornering and a smooth surface is not desirable....  my apologies for being late to the party.

I will do this to a few sets just sell them for the same price on a first come first serve basis.  Unless everyone want's  the knurl then I can just add it to all of them.

[Travman]

Any progress on the replacement pegs?

[Some Dude]

Yes they are made I just need to have them annodized which I hope to have done soon.

[Travman]

Thanks for the update.  My Cycle Cat rearsets are black, so I'd prefer black foot pegs.  However, if you have trouble getting them anodized I'd gladly buy them without anodizing. 

Just a general question for anyone:  Are the passenger's pegs the same as the rider's pegs?

[Munch]

Holler when you have some ready. I'm in for a pair!

[Some Dude]

Spoke to the anodizer today and the pegs will be ready tue. or wed. So I should be shiping by the end of next week.

Heres what I have that's not already spoken for

6 Sets Black
5 Sets Silver

Please let me know if your interested I'm not sure how long they will last.
$55 Shipped per set.

Thanks

[Some Dude]

Picked them up tonight will start shipping tomorrow.  Here are some pics.  They turned out very nice

[uglyducky]

Picked them up tonight will start shipping tomorrow.  Here are some pics.  They turned out very nice

      [moto]

[Travman]

I received my pair in the mail about 2 days ago.  They pegs are perfect replacements with a perfect fit.  He even included the mounting screw.  The knurling is a little less deep.  That is about the only difference I could notice.  Thank you Mr. Dude.  My passenger now has somewhere to put her feet.