News:

This Forum is not for sale

 

Replacement foot pegs for Cycle Cat

Started by Some Dude, February 19, 2010, 05:47:40 PM

Previous topic - Next topic

Some Dude

In this thread Here we had a little discussion going about replacing CC footpegs.  I decided I would draw them up and get a quote on having some made.  I have modeled it up and I need to know if it looks right. I have 1 peg to measure but the outside is ground off, so I'm kind of guessing at the overall length, and what the outer end should look like.  I have asked for someone to post a picture and an overall length but I haven't seen it yet.

Here is what I have


Right now I have the length of the foot portion at 75mm (2.95In) and the overall lenght is 81mm (3.2In)
can those of you who have them look this over and let me know what changes are needed?
I would also like to know who is interested and what colors we need so I can get a proper quote.

Thanks
Bike Info
99 m900s                                                Sbk forks
41mm FCR's
Dyna coils
944 hi comp pistons
heads ported and polished
larger valves
new valves and cams
aluminum fly wheel & clutch basket
[bacon]                                                                                              [bacon]                                                                                          [

stopintime

My measurements with a simple tool:
(might not be totally accurate)

75/81 mm is correct
Widest part 25mm
The part that goes into the peg carrier, 15mm

For me, they have worked much better with homemade knurls on the widest part, the ring on the outer edge.
Silver and black will do fine, I guess.

Good luck - keep us posted [thumbsup]
252,000 km/seventeen years - loving it

Javamoose

What type of quantity are you looking to have made?  Two or Four is gonna give you a fairly high cost...if you're looking at getting a few dozen made up however...  ;D
2000 M750

Some Dude

QuoteWhat type of quantity are you looking to have made?

That's what I'm trying to figure out here.  I know the bigger the order the lower the cost which is why i'm hoping to get alot of interest here.
Bike Info
99 m900s                                                Sbk forks
41mm FCR's
Dyna coils
944 hi comp pistons
heads ported and polished
larger valves
new valves and cams
aluminum fly wheel & clutch basket
[bacon]                                                                                              [bacon]                                                                                          [

fasterblkduc

I'm interested. I think I can find a couple others who are too. I'll try to get you measurements today.
Atomic Racing
Zalusky Advanced Riding School Lead instructor
2010 partners:
Komodo Gear, Motorex, Studio299, Moto Primo, Caztek, Chickenhawk

Travman

I need one Cycle Cat replacement peg for my passenger.  I would probably take at least three so I would have some extras. 

Some Dude

Well I got my first quote back today and it wasn't very promising. 
For 10 pieces they were about $31 ea.
and 20 pieces they were about  $22 ea.
That doesn't even include anodize.

I will send it out for a few more quotes and see what comes back.
Bike Info
99 m900s                                                Sbk forks
41mm FCR's
Dyna coils
944 hi comp pistons
heads ported and polished
larger valves
new valves and cams
aluminum fly wheel & clutch basket
[bacon]                                                                                              [bacon]                                                                                          [

Travman

I would pay $31 in order to have a rear passenger peg.  Even if it was bare aluminum.  Right now my passenger just puts her foot on the foot protection piece behind the peg. 

Ducatl

That seems pretty reasonable to me, pricing wise.

stopintime

252,000 km/seventeen years - loving it

Some Dude

Sorry I took so long.  I've been too busy.  It looks like I can get these made and anodized and sell them for about $25ea or $50 per set.  It will still be a couple weeks before the shop can make them.  I had them build me 2 just to make sure they would work.  They are a little different than the original but, they bolt right up and should work just fine. Here are a few pics, the peg in the middle is an original cycle cat peg.  If you would like some please send me a pm and let me know which color and how many.  Thanks



Bike Info
99 m900s                                                Sbk forks
41mm FCR's
Dyna coils
944 hi comp pistons
heads ported and polished
larger valves
new valves and cams
aluminum fly wheel & clutch basket
[bacon]                                                                                              [bacon]                                                                                          [

manwithgun

Quote from: stopintime on February 20, 2010, 12:19:07 AM

For me, they have worked much better with homemade knurls on the widest part, the ring on the outer edge.
Silver and black will do fine, I guess.

Agreed with stopintime.  It can always be done by the end user with a dremel or other grinder but if you wanted to offer an upgrade to the Cycle Cat Peg, look into adding a textured lug/knurled lip to the outer edge.  This is where the ball of your inside foot rests while cornering and a smooth surface is not desirable....  my apologies for being late to the party.
I ride both kinds,   Country, and Western.....

Travman

They pegs look great. [clap]  How soon do you think they will be available to ship?  I have PM'ed you my request. 

The Bearded Duc

Don't know if theses are the ones you're looking for, as I can't see the pics, but motowheels.com has replacement Cycle Cat foot pegs.

http://www.motowheels.com/italian/myproducts.cfm?parentcategoryid=1395%7CMonster%20Controls&productID=6851&showDetail=1&categoryID=1376|Monster%20Foot%20Controls&vendoridtodisplay=0&filterFor=&collection=168%7CEuropean%20Motorcycle%20Parts
2001 M750 - Sold
2006 S2R 800 - She's just darling

stopintime

Quote from: duc750 on April 21, 2010, 09:21:17 AM
Don't know if theses are the ones you're looking for, as I can't see the pics, but motowheels.com has replacement Cycle Cat foot pegs.

Those are the toe pegs though, but good to know they are available. I got the last of MotoWheels extender toe pegs GL-1 two years ago.
252,000 km/seventeen years - loving it